|
Jaguar
S-Type
Technical Service Bulletin (TSB) |
|
3-158 [PDF] |
Wood Veneer Repair Program |
|
JTB00040NAS2 |
Version 2 of this bulletin replaces
previously published bulletins JTB00040 & JTB00030 |
|
JTB00066NAS3 |
Ticking / Bubbling Noise From Behind Fascia /
Instrument Panel |
|
JTB00103 |
Unable to Reduce Climate
Control Outlet Temperature -Diagnostic Procedure |
|
JTB00183 |
S-Type Does Not Cool sufficiently |
|
S100-01 |
S-TYPE – Essential Tools –Specifications |
|
S100-02 |
Passenger Air Bag Warning Label –Mandatory
Installation |
|
S100-03 |
Engine Oil – Viscosity/Temperature Chart |
|
S100-05 |
S-Type Enhancement Program - Service Action
S120 |
|
S100-05a |
S-TYPE Enhancement Program –Service Action
S120 |
|
S100-06 |
Extended Life Coolant (XLC) –Identification
–Precautions |
|
S100-09 |
Steering Wheel Vibration –Revised Power
Assisted Steering Rack |
|
S100-10a |
Thump From Rear Of Vehicle –Differential
Mount Bushings –Install Bushing Inserts |
|
S100-11 |
Drive Belt Noise After Cold Start
–Supercharger –Revised Drive Belt Available |
|
S100-12 |
Buzzing/Knocking Noise After Start Or
WithIgnition On – Adaptive Speed ControlModule – Repair
Procedure |
|
S100-18 |
Engine Drive Belt –Noise Issues –Diagnosis |
|
S100-S503 |
Enhanced Dealer PDI Process –3-Month Trial
Period – USA Market OnlyService Action S503 |
|
S204-02 |
Wheel Nuts – Clarification of
TorqueSpecification |
|
S204-03 |
Suspension Springs - Use of Packers/Spacers |
|
S204-04 |
Front Wheel Bearing/Wheel Speed Sensor
–Replacement – Installation Precautions |
|
S204-05 |
Rear Suspension Toe Links (Tie RodAssemblies)
– Larger Mounting Stud –Modification Procedure |
|
S204-07a |
Vibration Felt Through Steering Wheel
orSeats – Wheels/Tires –Diagnostic Procedure |
|
S204-08 |
Clunk From Front Stabilizer Bar –Revised
Design Bushings –Installation Procedure |
|
S204-10 |
Permanent ‘High Spot’ MarkingOn Tire Inboard
Sidewall –Information |
|
S204-11 |
Shock Absorbers –Revised Warranty
Replacement Policy |
|
S204-12 |
Premature Wear On Inner Tread Edge –Front
Tires –Modified Toe Specification |
|
S204-R136 |
Recall R136 –Front Lower Ball Joints –Check
Torque or Replace |
|
S204-S150 |
Rear Suspension –Check/Reset Rear Toe
–Service Action S 150 |
|
S204-S516 |
Spare Tire Speed Restriction Label –Lack of
Adhesion –Service Action S516 |
|
S205-01 |
Rear Axle Shaft Damage –Use X-TYPE Special
Tools –Removal Procedure |
|
S205-02 |
Rear Drive Halfshaft –Change In
Specification From Hollow ToSolid Shafts |
|
S206-02 |
Installation of Wheel Speed Sensorin Front
Wheel Bearing Housing –Sealing Procedure |
|
S206-03 |
Vibration When Braking(Comeback Visits) –
Brembo Brakes –Disc/Hub Optimization Procedure |
|
S206-04 |
Electronic Park Brake (EPB) –Re-Calibration
Procedure |
|
S206-05 |
Brake Caliper Flexible Hose –Washer Now
Available Separately |
|
S206-R166a |
Unintended Rear Wheel Braking –No Park Brake
Warning Lights Displayed –RECALL R166 |
|
S211-01 |
Noise From P.A.S. –Replace Check Valve |
|
S211-03 |
Lack of Power Assist –Steering Control Valve
Actuator –Replacement Procedure |
|
S211-04 |
Squeaking Noise –Power Steering System
–Flush System |
|
S211-04a |
Squeaking Noise .Power Steering System
.Flush System |
|
S211-04a2b |
Squeaking Noise –Power Steering System
–Repair Procedure |
|
S211-05 |
Lower Steering Column Area Whistle Noise
–Transfer Pipe Flush “Rush” –Install Revised Steering Rack |
|
S303-02 |
3.0 L V6 Knock Sensor Designations –Not
Based On Cylinder Bank Designations –Clarification |
|
S303-03 |
Valve Clearance Adjustment Tool 303-693
–3.0 L V6 Engine –Procedure |
|
S303-04a |
New Design Dipstick –Identification
–Increased Oil Fill Quantity |
|
S303-07 |
Drivability Issues –Diagnostic Checks –Check
Sheet |
|
S303-08 |
Oil Leaks From Oil Filter –Filter Loosens
–Revised Tightening Method |
|
S303-09 |
MIL Illuminated – 3.0 L V6 –False Flagging
of DTC P1383 or P1388 –Reprogram PCM |
|
S303-11a |
Overheating –Thermostat Stuck Closed
–Revised V8 Thermostat Available |
|
S303-12 |
Misfire/Non-Start –Water Ingress Into Spark
Plug Wells –Revised On-Plug Coil Cover |
|
S303-14 |
MIL Illuminated - V6/V8 Engine Management
Diagnosis - Flowcharts |
|
S303-15 |
Coolant Pumps –Impeller Material –Pump
Replacement Issues |
|
S303-16 |
V6 3.0L Stripped Engines –Additional Parts
Required For LaterSpecification Front End Accessory Drive |
|
S303-17 |
Check Engine MIL/DTC P0341 And P0346 –V6
Engine –Repair Procedure |
|
S303-19 |
Rough Idle/Restricted Performance/DTCs P0174, P0171, P0301
to P0308 P1316 and P1582 - Loose Air Cleaner Pipe |
|
S303-21 |
Rough Idle/Hesitation –Contaminated Fuel
Injectors –Cleaning Procedure |
|
S303-23 |
Cooling System –Draining, Filling and
Bleeding –SRO Time Revision |
|
S303-24a |
V6 Engine MIL Lamp On/DTC P0332 –Water Entry
In Knock Sensor Connector –Install Sealing Patch |
|
S303-25 |
3.0L V6 Restricted
Performance 4100-4300rpm / MIL ON – DTC P0300 to P0306,
P1313,P1314 or P1316 – Reflash ECM |
|
S303-26 |
Engine Detonation/Pinging DuringAcceleration
From Steady-State Driving –Reconfigure ECM |
|
S303-S137 |
V6 Engine Knocking Sound –Contaminated Oil
Cooler –Service Action S137 |
|
S303-S139a |
S-TYPE PCM Reflash –Service Action S139 |
|
S303-S145 |
Coolant Level Sensor Contamination –Disable
Sensor –Service Action S145 |
|
S303-S151 |
Retorque Idler Pulley –Supercharged Vehicles
–Service Action S151 |
|
S303-S157 |
Vehicles With 3.0L V6 Exchange Engines
–Potential Thrust Bearing Failure –Service Action S157 |
|
S303-S158 |
Poor Idle/Check Engine MIL – V6 Engines
–Improved Breather Elbow –Service Action S158 |
|
S303-S159 |
Engine In Limp Home/Check Engine MIL –Water
Ingress into Throttle Position Sensor –Service Action S159 |
|
S303-S511 |
Oil Leak From Engine Oil Drain Plug .V8
Engines Only .Service Action S511 |
|
S303-S518 |
V6 Coolant Pump Outlet Hose –Replace With
Correct Specification –Service Action S518 |
|
JTB00070 |
Transmission Noise
During Gear Shifts – Repair Procedure |
|
S307-01 |
Selector Lever (Gear
Shift) Interlock –Service Release Procedure |
|
S307-02 |
Stuck Ignition Key
–Modify J-Gate Interlock Lever –Service Action S114 |
|
S307-03 |
DTC P0741 – Torque
Converter Clutch DoesNot Lock Up – Missing O-ring |
|
S307-03a |
DTC P0741 –Torque
Converter Clutch Does Not Lock Up –Missing Seal Ring |
|
S307-05 |
Transmission Fluid
Leaks –Cooler Hoses –Install Additional Hose Clamp |
|
S307-06 |
Difficulty Selecting
Range –Stiff Or Restricted Movement –Revised Selector Lever
Cable |
|
S307-07 |
Harsh/Slow Shifts –3.0
L V6 Vehicles –Reprogram PCM |
|
S307-09 |
Harsh Shifts –
Transmission MIL IlluminatedWith Reverse Selected –DTC P0736
Stored |
|
S307-10 |
MIL Illuminated/DTC
P0606 –Shift Quality/Driveability Issues – ZF 6HP24 –Reprogram
TCM |
|
S307-11 |
Growling Noise In 4th
Gear During Warmup –V6 Engines - ZF6HP26 Transmission
–Reconfigure TCM |
|
S307-12 |
Driveline Clunk/Knock
When Downshifting –ZF 6HP26 Automatic Transmission –Repair
Procedure |
|
S307-13 |
MIL Illumination –DTC
P0741 –Replace Torque Converter |
|
S307-13V3 |
MIL Illumination - DTC
P0741 - Replace Torque Converter |
|
S307-14 |
Surge During Warm up at
40mph to 60mph |
|
S307-14UK |
Surge During War up at
40mph to 60mph |
|
S307-15 |
Squeal/Squeak Noise
During Acceleration .Flush And Replace ZF Transmission Fluid
.Repair Procedure |
|
S307-16 |
Selector Lever
Difficult To Disengage FromPark – Revised Internal Control Lever
–Repair Procedure |
|
S307-17 |
Harsh Transmission
Shifts –Adaptive Shift Strategy Drift –Reprogram TCM & ECM |
|
S307-17 |
6 Speed Transmission -
Harsh Shifts - Adaptive Shift Strategy Drift - Reprogram TCM &
ECM |
|
S307-18 |
Automatic Transmission
Remove/Install –New Workshop Procedure –Revised Labor Times |
|
S307-19 |
5-Speed Transmission –
Erratic or HarshShifts – Valve Body Kit Available –Repair
Procedure |
|
S307-20 |
Inability to Shift
Gears –Selector Lever Moves Freely Through J-Gate– Repair
Procedure |
|
S307-R513 |
Incorrect Gear
Selection .ZF 6 Speed Automatic Transmission .Recall Action R513 |
|
S308-01 |
Manual Transmission
Remove/Install –New Workshop Procedure –Revised Labor Times |
|
No 4th or 5th gear |
4-5 Pre-Stroke Valve
Spring |
|
S310-01a |
Loss of Engine
Performance – Low FuelPressure – Replace Fuel Delivery
ModuleHose – Service Action S144 |
|
S310-02 |
Erratic Fuel Gauge
Reading .Fuel Tank Sender .Repair Procedure |
|
S310-04 |
Erratic Fuel Gauge
Reading .Fuel Tank Sender . S-TYPE R .Repair Procedure |
|
S310-06 |
Fuel Filler Door
Inoperative –Actuator Binding –Modification Procedure |
|
S310-07 |
Fuel Gauge Failure or
Intermittent Operation –Fuel Level Sender Available Separately
–Replacement Procedure |
|
S310-S515 |
Fuel Filler Cap Seal
Durability –Revised Seal Ring –Service Action S515 |
|
JTB00183 |
Air Conditioning System
Not Cooling Sufficiently |
|
S412-01 |
A/C Compressor
–Transferring Drive Clutch to new Compressor– Clearance
Adjustment |
|
S412-02 |
Air Conditioning
–Refrigerant Circuit –Leak Reporting |
|
S412-03 |
A/C Odor –Applying Odor
Control Treatment –Procedure |
|
S412-04 |
Inaccurate Ambient
Temperature Reading InCold Weather – Relocate AmbientTemperature
Sensor – Modification Procedure |
|
S412-05 |
Climate Control Sysem
Lock-up .23°C Displayed Continuously .Update Telematics Software |
|
413-02 |
Control Modules – PECUS
Display Messages |
|
JTB00014 |
Additional Diagnostics
for Instrument Cluster |
|
S413-01 |
Sticking Needles
–Speedometer & Tachometer –Correction Procedure |
|
S413-02 |
False Warning Lamp
Illumination –Revised Instrument Cluster –Repair Procedure |
|
S414-01 |
Battery – Quiescent
Drain Current –Specifications |
|
S414-02 |
High Quiescent Drain
–Intermittent Loss of Permanent Power Feed –Install Forward
Harness Bypass Lead |
|
S415-01 |
AM Interference
–Relocate Trunk Harness –Service Modification |
|
S415-02 |
Poor AM or FM Reception
–Diagnostic Procedures –Modification Procedure |
|
S417-01 |
Daytime Running Lamps
–Enable/Disable |
|
S417-03 |
Loose Mounting –Center
High Mounted Stop Lamp –Repair Procedure |
|
S417-04 |
Headlamp Internal
Condensation –Acceptable Levels –Repair Guidelines |
|
S418-01 |
Brake Pedal Switch –
Revised Specification –Installation Procedure |
|
S418-02 |
Installation Of New
FEM, REM, and DDM –Incorrect VID Block –Use Manual Configuration
Option |
|
S419-01 |
Navigation System
Diagnosis –Access to Diagnostic Menu – Troubleshooting |
|
S419-02 |
Compass Calibration –
Procedure –Not in JTIS |
|
S419-03 |
Aftermarket Rear Window
Tint –Interference With Reception of GPS Signal |
|
S419-05 |
Difficulty Inputting
Commands –Voice Activated Control System –Guidelines |
|
S419-07 |
Voice Control System
–Changes Starting 2001 MY –Differences From 2000 MY Operation |
|
S419-09 |
Digital Telephone
System –Diagnostic Flowcharts –Harness And Connector Checks |
|
S419-11 |
Remote Key Fob
–Factory-Programmed To Memory Position 1 –Introduction |
|
S419-12 |
Passive Anti -Theft
System (PATS) –Diagnostic Flowcharts |
|
S419-13 |
Telematics Concerns
–Navigation System Software –Installing Latest Level |
|
S419-14 |
Telematics Issues
.Check For Latest Software .Update Procedure |
|
S419-15 |
Navigation System
–Diagnostic Procedures |
|
S419-S140a |
Jaguar Assist Module –
USA Vehicles Only –Install Later Revision Level –Service Action
S140 |
|
S419-S155 |
Telephone Echo On
Vehicles With PremiumIn-Car Entertainment (ICE) – Replace
AudioAmplifier – Service Action S155 |
|
S501-01 |
Front Seats – Removal
–Handling Precautions |
|
S501-02 |
Uneven Operation of
Windows or Sliding Roof– Seals Contaminated by Polish
–Recommendations |
|
S501-03 |
Installation of Child
Seat Tether MountingEyes – Dimensions – USA Vehicles |
|
S501-04 |
Wind Noise –Check Door
Mirror Gaps –Repair Procedure |
|
S501-06 |
Memory Buttons Hot To
Touch –Component Serviceability –Repair Procedure |
|
S501-07 |
Ashtray Latch
Malfunction –Revised Latch –Replacement Procedure |
|
S501-08 |
Broken Fasteners –Front
Seat Squab Covers –Replace Broken Fasteners |
|
S501-09 |
Water Leaks -
Diagnostics |
|
S501-10 |
Leather Upholstery –
Care & Maintenance |
|
S501-11 |
Water Leakage Into Rear
Footwells –Add Drain Holes –Modification Procedure |
|
S501-12 |
Luggage Compartment Lid –Difficulty Opening
–Repair Procedures |
|
S501-13 |
Inoperative Windshield Washer –Operated
While Frozen –Upgrade Fuse To 15 amp |
|
S501-14 |
Memory Systems –Driver’s Seat, Steering
Column, Door Mirrors– Diagnostics |
|
S501-15 |
Front Door Replacement –Adapting Window
Regulators To New StyleFront Door – Adaptor Kit |
|
S501-16a |
Sliding Roof Does Not Close Properly/Bounces
Open – Loss Of Calibration –Replace Sliding Roof Motor |
|
S501-17 |
Loose Rearview Mirror –Reinstalling Mirror
Mounting Block OnWindshield – Installation Procedure |
|
S501-18a |
Remote Transmitter Does Not Unlock Vehicle–
Vehicle Locked For Extended Period –Install Revised Driver Door
Module |
|
S501-18a2 |
Remote Transmitter Does Not Unlock Vehicle.
Vehicle Locked For Extended Period .Install Revised Driver Door
Module |
|
S501-19 |
Locking or Unlatching Issues –Diagnostic
Information |
|
S501-20 |
Loss of Seat Memory –Reprogram or Replace
DSM –Repair Procedure |
|
S501-21 |
Sliding Roof One-Touch Issues –Resynchronize
Roof Panel & Reprofile Spring– Repair Procedure |
|
S501-22 |
Shield For Roof Opening Panel SlidesForward
While Braking – Loose Fit –Install Velcro Strips |
|
S501-23 |
Customer Intermittently Locked Out OfVehicle
After Closing Door .Install New Door Handle Damper |
|
S501-23a |
Customer Intermittently Locked Out OfVehicle
After Closing Door –Install New Door Handle Damper |
|
S501-24 |
Window Regulator and Motor –Available
Separately –Repair Procedure |
|
S501-25 |
Sun Visor Mirror Bulb –Now Available
Separately –Replacement Procedure |
|
S501-26 |
Supplemental Restraint System (SRS) –Flash
Codes & PID Code Definitions –Diagnostics |
|
S501-27 |
Electrical Seat Judder, Noisy/Inoperative
–Lubrication/Motor –Repair Procedures |
|
S501-28 |
Windshield Wiper Performance Issues –KATS
Contamination/Debris/Rubber Deterioration – Recommendations |
|
S501-29 |
Interior Mirror Compass –Compass Reading
Incorrectly –Reroute Wiring |
|
S501-M01 |
Airbag Deactivation Shunt Kit –Installation
Instructions |
|
S501-R134 |
Recall R134 –Front Seat Belt Buckle –Replace
With Proper Specification Buckle |
|
S501-S142a |
Rear Door Glass Inoperative in Hot Climates
–Detached Regulator Mounting – ReplaceRegulators – Service
Action S142 |
|
S501-S161 |
Wind Noise From Roof Opening Panel –Panel
Profile Set Incorrectly –Service Action S161 |
|
S501-S163 |
Windshield Washer Hose Routing –Left Wiper
–Service Action S163 |
|
S501-S164 |
Rain Sensing Wipers –Remove Diode/Install 5
Amp Fuse –Service Action S164 |
|
S527r3 |
Key Fob Modification |
|
S600-S474a |
Part-Load Engine Breather – Partial
Blockageof Restrictor – Scheduled Cleaning –Service Action S474 |
| S,NAV |
NAVIGATION EXCHANGE PROGRAMProduct Problem
Report: S-TYPE |
|
SRS System |
Supplementary Restraint System |
|
Wheel Bearings |
Front Wheel Bearing Replacement Precautions During
Installation |
|
|
|
